Accessories
See all our high quality sludge separators, spare parts and more below. Contact our team for further information.
ECOTHERM Magentic-Dynamic Separator
The Magnetic-Dynamic Separator (EMDS) is a reliable solution that protects systems from corrosion, scale, and sludge without the need for chemical additives. It reduces the content of mineral substances, lowers electrical conductivity, and corrects the pH value of the water. By using the EMDS, the water quality required by the VDI 2035 guideline can be achieved and maintained effectively.
Advantages of the Magentic-Dynamic Separator “EMDS”
Requirements
✓ Flushing of new equipment is not required. After switching on the water circuit, mobilized impurities are quickly and effectively separated.
✓ The water quality according to guideline VDI 2035 is achieved within a short time
✓ Corrosion protection (magnetite protection layer) is achieved shortly after commissioning of the EMDS
✓ The plant efficiency is maintained by the EMDS during the entire operating time
✓ Clear water operation is achieved after a very short time
✓ Significant reduction of conductivity
✓ Correction of the pH value
✓ Water hardness is reduced to a negligible value close to zero
✓ All the above results are also valid for existing plants
✓ Incrustations and deposits are broken down and removed
✓ Surface heating systems become sludge-free. Old systems are rehabilitated
✓ A system separation of underfloor heating and heat generators is not necessary
Read more in our new brochure: ECOTHERM Magnetic-Dynamic Separators (PDF)
Accessories | Article | Description | |
![]() | TH1/2”x60M16x1,5 | 59210001 | Thermowell with cable fitting for temperature sensor, L = 60 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x160M16x1,5 | 59210000 | Thermowell with cable fitting for temperature sensor, L = 160 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x200M16x1,5 | 59210004 | Thermowell with cable fitting for temperature sensor, L = 200 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x60K | 59220000 | Thermowell with clamping screw for Thermometer, L = 60 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x160K | 59220002 | Thermowell with clamping screw for Thermometer, L = 160 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x200K | 59220005 | Thermowell with clamping screw for Thermometer, L = 200 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x160LS | 49220020 | Thermowell for Temperature sensors with long shaft, L = 160 mm, Inside Ø 8 mm, stainless steel 1.4571 |
![]() | TH1/2”x250LS | 49220021 | Thermowell for Temperature sensors with long shaft, L = 250 mm, Inside Ø 8 mm, stainless steel 1.4301 |
Accessories | Article | Description | |
![]() |
NBFL270/6 |
59150002 |
Blank flange, flange NW 200, 6mm, stainless steel 1.4571 |
NBFL270/10 |
59150005 |
Blank flange, flange NW 200, 10mm, stainless steel 1.4571 | |
![]() |
FLM1,5/270 |
59110000 |
Flange with 6/4” sleeve for electric screw-in heaters, flange NW 200 stainless steel 1.4571 |
![]() |
FL0,75/70 |
59120003 |
Flange for tube heat exchanger Type H (heating water) WT-18-E und WT-25-E, Flansch NW 200 |
![]() |
FL0,75/120 |
59120004 |
Flange for tube heat exchanger Type H (heating water) WT-36-E und WT-45-E, Flansch NW 200 |
![]() |
FL0,75/85 |
59120005 |
Flange for tube heat exchanger Type D (steam) WBE04-D bis WBE07-D, Flansch NW 200 |
![]() |
FL0,75/115 |
59120006 |
Flange for tube heat exchanger Type D (steam) WBE10-D bis WBE15-D, Flansch NW 200 |
![]() |
FL1,00/200 |
59120007 |
Flange for tube heat exchanger Type D (steam) WBE20-D und WBE26-D, Flansch NW 300 |
![]() |
FL1,25/180 |
59120008 |
Flange for tube heat exchanger Type D (steam) WBE30-D und WBE40-D, Flansch NW 300 |
![]() |
GD 265(60×180)x4 |
23640003 |
Flat gasket 265 (60 x 180) x 4 mat.: EPDM ( 70° Shore) to FL-NW200 |
![]() |
KD 165/205/2 |
23610000 |
Flange gasket Klingerit 265/205×2 C-4400 |
Accessories | Description | |
![]() |
|
|
Accessories | Description | |
![]() |
NBVS |
Screw-type blank cap for WT-implementation 3/4” stainless steel 1.4571, (Set = 2 Pcs.) |
![]() |
SKST-1/2” |
Stainless steel-blanking plug 1/2″, stainless steel 1.4571 |
![]() |
SKST-3/4” |
Stainless steel-blanking plug 3/4″, stainless steel 1.4571 |
![]() |
SKST-1” |
Stainless steel-blanking plug 1″, stainless steel 1.4571 |
![]() |
SKST-5/4” |
Stainless steel-blanking plug 5/4″, stainless steel 1.4571 |
![]() |
SKST-6/4” |
Stainless steel-blanking plug 6/4″, stainless steel 1.4571 |
Accessories | Description | |
![]() |
|
|
![]() |
|
|
![]() |
|
|
![]() |
|
|
![]() |
|
|
Accessories | Nominal kW | Connection Volt | Loading W/cm2 | Bolting | Immersion mm | Thermostat (integrated) | |
EHK-I-2000 | 2.00 | 230/400 | 7.81 | 6/4″ | 250 | yes | |
EHK-I-2250 | 2.25 | 230/400 | 3.50 | 6/4″ | 500 | yes | |
EHK-I-3000 | 3.0 | 230/400 | 4.57 | 6/4″ | 500 | yes | |
EHK-I-4500 | 4.5 | 230/400 | 6.85 | 6/4″ | 500 | yes | |
EHK-I-6000 | 6.0 | 230/400 | 9.13 | 6/4″ | 500 | yes | |
EHK-I-7500 | 7.5 | 230/400 | 11.42 | 6/4″ | 500 | yes | |
EHK-I-9000 | 9.0 | 230/400 | 8.51 | 6/4″ | 750 | yes | |
EHK-I-12000 | 12.0 | 230/400 | 11.35 | 6/4″ | 750 | yes | |
EHK-I-15000 | 15.0 | 230/400 | 8.50 | 6/4″ | 1,150 | not possible | |
EHK-I-25000 | 25.0 | 400 | 6.80 | 2 1/2″ | 1,100 | not possible |
Accessories | Nominal | Connection | Load | Area | Top Ø | Immersion | Tube Ø | |
kW | Volt, AC | Ampere | W/cm2 | mm | mm | mm | ||
EHK-K-2000 | 2 | 230/400 | 2.9 | 5.03 | 47 | 370 | 50 | |
EHK-K-2500 | 2.5 | 230/400 | 3.6 | 5.25 | 47 | 425 | 50 | |
EHK-K-3000 | 3 | 230/400 | 4.3 | 5.39 | 47 | 480 | 50 | |
EHK-K-4000 | 4 | 400 | 5.8 | 4.41 | 47 | 700 | 50 | |
EHK-K-4000 | 4.5 | 400 | 6.5 | 4.23 | 47 | 800 | 50 | |
EHK-K-5000 | 5 | 400 | 7.2 | 4.01 | 47 | 900 | 50 | |
EHK-K-6000 | 6 | 400 | 8.7 | 4.12 | 47 | 1,050 | 50 | |
EHK-K-7000 | 7 | 400 | 10.1 | 4.14 | 47 | 1,200 | 50 | |
EHK-K-8000 | 8 | 400 | 11.6 | 3.99 | 47 | 1,400 | 50 | |
EHK-K-9000 | 9 | 400 | 13.0 | 3.88 | 47 | 1,600 | 50 | |
EHK-K-10000 | 10 | 400 | 14.5 | 4.04 | 47 | 1,800 | 50 |
Accessories | Frame | Flange | Regulating | Heaters/ | Heater | Voltage | Ø of tank | |
| ||||||||
EHK-KF-2000 | 2 kW | 1 | 1 | 1 | 2 kW/230V | 2x230V/50Hz | 500 mm | |
EHK-KF-3000 | 3 kW | 1 | 1 | 1 | 3 kW/230V | 2x230V/50Hz | 500 mm | |
EHK-KF-4000 | 4 kW | 1 | 1 | 2 | 2 kW/230V | 3x230V/50Hz | 500 mm | |
EHK-KF-6000 | 6 kW | 1 | 1 | 3 | 2 kW/400V | 3x400V/50Hz | 500 mm | |
| EHK-KF-7500 | 7,5 kW | 1 | 1 | 3 | 2.5 kW400V | 3x400V/50Hz | 500 mm |
EHK-KF-9000 | 9 kW | 1 | 1 | 3 | 3 kW/400V | 3x400V/50Hz | 500 mm | |
EHK-KF-12000 | 12 kW | 1 | 1 | 3 | 4 kW/400V | 3x400V/50Hz | 750 mm | |
| ||||||||
EHK-KF-15000 | 15 kW | 2 | 2 | 3 | 2.5 kW/400V | 3x400V/50Hz | 500 mm | |
EHK-KF-18000 | 18 kW | 2 | 2 | 3 | 3 kW/400V | 3x400V/50Hz | 500 mm | |
EHK-KF-24000 | 24 kW | 2 | 2 | 3 | 4 kW/400V | 3x400V/50Hz | 750 mm | |
| ||||||||
EHK-KF-30000 | 30 kW | 2 | double-pole | 6 | 2.5 kW/400V | 3x400V/50Hz | 800 mm | |
EHK-KF-36000 | 36 kW | 2 | double-pole | 6 | 3 kW/400V | 3x400V/50Hz | 800 mm |
Accessories Type | Description | |
FSA-402 | Titanium electrode 402 mm Art.60000038 (for Storage from 200 – 540 Liter) | |
FSA-832 | Titanium electrode 832 mm Art.60000043 (for Storage from 750 Liter) | |